BS5-T2M BS5-K2M BS5-L2M 微型光电传感器
BS5-T2M BS5-K2M BS5-L2M 微型光电传感器
产品价格：￥76（人民币）
  • 规格：BS5-T2M BS5-K2M BS5-L2M
  • 发货地：深圳
  • 品牌：
  • 最小起订量：1个
    • 立即询价 进入商铺
    深圳市定兴机电设备有限公司
    诚信商家
    会员级别：钻石会员
    认证类型：企业认证
    企业证件：通过认证
    认证信息：深圳市定兴机电设备有限公司

    商铺名称：深圳市定兴机电设备有限公司

    联系人：蒋小姐（小姐）

    联系手机：

    固定电话：

    企业邮箱：1152816556@qq.com

    联系地址：深圳市宝安区沙井德普电子城

    邮编：518000

    联系我时，请说是在地方电气网上看到的，谢谢！

    商品详情

      BS5-T2M BS5-K2M BS5-L2M 微型光电传感器 韩国奥托尼克斯光电开关BS5-L2M
      奥托尼克斯 AUTONICS 传感器 BS5-T2M BS5-K2M BS5-L2M
      奥托尼克斯Autonics微型/槽型/U型光电开关/传感器BS5-L2M

      微型光电传感器BS5系列，接插式接线方式方便接线，具有多种不同的外形（K,T,L,Y,V型）,便于安装。采用宽范围电源电压，易于连接各种IC,继电器，PLC等。发光器/接收器窗口采用防尘保护设计，信赖度更高，可在较差的环境下使用。
      超小型,内置放大器,NPN集电极开路输出
      多种型号(K,T,L,Y,V型)适用于多种不同应用场合
      通过控制线可选择Light ON/Dark ON模式
      高速响应频率: 2kHz
      宽电源电压范围: 5-24VDC(易于连接不同的IC,继电器,可编程控制器)
      发射端/接收端窗口防尘保护设计
      红色指示灯可指示动作状态
      通过连接头接插方式连接
      微型光电传感器

      主要特性
      * 超小型,内置放大器,NPN集电极开路输出
      * 多种型号(K,T,L,Y,V型)适用于多种不同应用场合
      * 通过控制线可选择Light ON/Dark ON模式
      * 高速响应频率: 2kHz
      * 宽电源电压范围: 5-24VDC
      (易于连接不同的IC,继电器,可编程控制器)
      * 发射端/接收端窗口防尘保护设计
      * 红色指示灯可指示动作状态
      * 通过连接头接插方式连接

      应用场合
      * 适用于小型高精密机械:LCD半导体设备,图像检测系统和运送装置执行机构
      * 适用于设定调色板位置,计算数量和检测旋转体的起始位置



      型号说明

      规格表


      Model NPN open collector output BS5-K2M BS5-T2M BS5-L2M BS5-Y2M BS5-V2M
      PNP open collector output BS5-K2M-P BS5-T2M-P BS5-L2M-P BS5-Y2M-P BS5-V2M-P
      Sensing distance 5mm fixed
      Sensing type Through-beam(Not modulated)
      Sensing target ?0.8×2mm Opaque materials
      Hysteresis 0.05mm
      Response time Light ON : Max. 20?, Dark ON : Max. 100?
      Response frequency 2kHz(refer to the measuring range of frequency response)
      Power supply 5-24VDC ±10%(Ripple P-P : Max. 10%)
      Current consumption Max. 30mA(at 26.4VDC )
      Light source Infrared LED(950nm)
      Operation mode Light ON / Dark ON selectable by control wire
      Control output NPN or PNP open collector output
      ? Load voltage : Max. 30VDC ? Load current : Max. 100mA ? Residual voltage : Max. 1.2V
      Protection circuit Reverse power polarity protection, Overcurrent protection
      Indicator Operation Indicator: red LED
      Connection Connector type
      Noise resistance ±240V the square wave noise(pulse width:1?) by the noise simulator
      Insulation resistance Min. 20MΩ(at 250VDC megger)
      Dielectric strength 1,000VAC 50/60Hz for 1 minute
      Light source Infrared LED(950nm)
      Vibration 1.5mm or 300m/s2 amplitude at frequency of 10 to 55Hz in each of X, Y, Z directions for 2 hours
      Shock 500m/s2(approx. 50G) in each of X, Y, Z directions for 3 times
      Environ- ment Ambient illumination Fluorescent lamp : Max. 1000? (Receiver illumination)
      Ambient temperature -20 to 55℃, storage : -25 to 85℃
      Ambient humidity 35 to 85%RH, storage : 35 to 85%RH
      Protection IP50(IEC standard)
      Material PBT
      Approval CE
      Unit weight Approx. 30g
      ※ The temperature or humidity mentioned in Environment indicates a non freezing or condensation environment.

      注意事项
      1.浪涌
      BS5系列未设置抗浪涌回路
      使用时请注意遵守EN标准
      2.外部光源
      该产品未设置防止外部光源干扰回路,请将接收器远离外部光源干扰
      3.布接方式
      和动力线、高压线等分开布线,以避免由此造成的误动作或产品损坏
      4.干扰发生源注意事项
      若微型光电传感器周围有机器产生干扰(开关稳压器,电机等),请将机器的屏蔽线F.G接地
      5.焊接(直接焊在端子上)
      直接焊接在端子上时不要超过3秒(最大温度260℃).确认焊接时离端子根部1.5mm以上.
      6.安装
      使用M3螺钉拧紧(最大力矩0.49N·m(5.0kgf·cm).拧螺钉时,请使用垫片(Φ6).请确认光电传感器收发光部分不与任何其他物体接触.若该部分划损时,产品会发生误动作.
      7.维护
      若传感器安装在有许多灰尘或潮湿的环境中,请注意清洁接收器,用干布擦干发射器和接收器，沾染灰尘会发生误动作
      8.其他
      安装传感器时远离:
      易腐蚀性气体,油,灰尘,水蒸汽,强酸强碱,强光

      ※请注意遵守上述说明以避免发生误动作或损坏产品

      注意安全

      Major Features
      * Microminiature, built-in amplifier, NPN open collector output
      * Various applications available with diverse line up(K, T, L, Y, V types)
      * Light ON/Dark ON mode selectable via control terminal
      * High-speed response frequency : 2kHz
      * Wide range of power supply : 5-24VDC
      (Easy to connect with various ICs, relays, programmable controllers)
      * Dust resistance structure protected by emitter/receiver window
      * Red LED for operation indication
      * Easy connection through optional connector sockets/cables

      Application Fields
      * Applicable to small high precision machines including LCD, semiconductor facilities, vision systems and actuator conveyer.
      * Suitable for determining palette position, counting coins and detecting rotator’s starting point

      Ordering Information



      Specification Table

      Model NPN open collector output BS5-K2M BS5-T2M BS5-L2M BS5-Y2M BS5-V2M
      PNP open collector output BS5-K2M-P BS5-T2M-P BS5-L2M-P BS5-Y2M-P BS5-V2M-P
      Sensing distance 5mm fixed
      Sensing type Through-beam(Not modulated)
      Sensing target ?0.8×2mm Opaque materials
      Hysteresis 0.05mm
      Response time Light ON : Max. 20?, Dark ON : Max. 100?
      Response frequency 2kHz(refer to the measuring range of frequency response)
      Power supply 5-24VDC ±10%(Ripple P-P : Max. 10%)
      Current consumption Max. 30mA(at 26.4VDC )
      Light source Infrared LED(950nm)
      Operation mode Light ON / Dark ON selectable by control wire
      Control output NPN or PNP open collector output
      ? Load voltage : Max. 30VDC ? Load current : Max. 100mA ? Residual voltage : Max. 1.2V
      Protection circuit Reverse power polarity protection, Overcurrent protection
      Indicator Operation Indicator: red LED
      Connection Connector type
      Noise resistance ±240V the square wave noise(pulse width:1?) by the noise simulator
      Insulation resistance Min. 20MΩ(at 250VDC megger)
      Dielectric strength 1,000VAC 50/60Hz for 1 minute
      Light source Infrared LED(950nm)
      Vibration 1.5mm or 300m/s2 amplitude at frequency of 10 to 55Hz in each of X, Y, Z directions for 2 hours
      Shock 500m/s2(approx. 50G) in each of X, Y, Z directions for 3 times
      Environ- ment Ambient illumination Fluorescent lamp : Max. 1000? (Receiver illumination)
      Ambient temperature -20 to 55℃, storage : -25 to 85℃
      Ambient humidity 35 to 85%RH, storage : 35 to 85%RH
      Protection IP50(IEC standard)
      Material PBT
      Approval CE
      Unit weight Approx. 30g
      ※ The temperature or humidity mentioned in Environment indicates a non freezing or condensation environment.

      User's Guide


      Caution for your safety

       

    0571-87774297